The company JANMOR, created in 1987, specializes in the production of ignition cable groups. We constantly increase the range of our offer and raise its quality. As far as the range of products is concerned, we almost fully satisfy the needs and requirements of our customers.
We are the only company in Poland and one of the few in the world to offer our production nearly in all possible raw material versions.
The “silicone version”, which is the best with regard to quality, is practically a true copy of the original group. The remaining versions are our response (and at the same time our offer) to the specific demand of our customers.
Our priority is always the care about the highest quality of our products and our customers; satisfaction. For that reason, since the second quarter of the year 2004 we have introduced state-of-the-art silicon cables, where used till now glass fiber braid was replaced by a special nylon tape. This tape is an extremely durable manner connects both layers of silicone and additionally increases strength and enhances other parameters of this cable. We are proud to inform you that for all our products we use solely the cables manufactured by the USA Company GENERAL CABLE - the most important world manufacturer of ignition cables for aftermarket. The mere name of this Company is a sufficient guarantee of the highest possible quality.
JANMOR is a company renowned not only in Poland. We export much more than half of our production to nearly twenty countries all over the world. In many countries, the logo of our company is tantamount to a quality symbol and synonym. The fact that these are not only words is evidenced by the certificates decorating the walls of our office.
The certificate from the English company BVQI, ISO 9001:2000, which we obtained in 2002 confirms and guarantees the professionalism of our company.
For the lifetime of every engine, an efficient and modern ignition system with its paramount part ignition cables is of the utmost importance. A contemporary engine needs more and more highly sophisticated electronic devices. There is less and less free room under the bonnet. In the direct neighbourhood of the engine, i.e. the usual location of cables, the temperature is very high.
All this considerably increases the demand for ignition cables and, especially, their boots.
That is why only highest quality materials can be used for their manufacture. It has been recognized for a long time now that the only material with all the indispensable parameters is silicone.
Hence our slogan: ALL YOU NEED IS MADE OF SILICONE (i.e. all cable layers and all boots).
The most important advice given by all the outstanding manufacturers of ignition cable groups is: even the best cables must be replaced. Our advice is to exchange the cables when you have covered:

• SILICONE: 150 000 km but with no age limitation
• NON-SILICONE: 30 000, 50 000 km or every 2 - 3 years.

Remember: use of JANMOR cables facilitates start-up, removes radio static, decreases fuel consumption and eliminates many other threats which, taken together, determine the reliability and economics of our vehicles.
According to our customers' needs and demand, we use in our products:
- the world's highest quality ignition cables 5, 7 and 8 mm diameter manufactured by the USA Company GENERAL CABLE
- silicone boots of identical shapes to the ones in original groups, especially recommended for use in gas installations; they o withstand temperatures of over 220 C;
- metal terminals identical to the ones in cables of renowned world companies; they are made of stainless acid-proof steel or elastic brass and tightened to obtain the highest quality of coupling directly on the isolated current-carrying wire (full contact).
All the raw materials used for the production of our ignition groups are nearly exclusively imported and conform to respective international quality standards. We guarantee that all the suppliers of raw materials which we use for manufacturing our groups have implemented the quality management systems ISO 9001 or QS 9000.
Moreover, we inform that in accordance with regulations binding in Poland we have the ITS Warsaw Certificate, valid until 2006, proving conformity with standard requirements, we also have a certificate authorizing us to use the safety sign B .
In April 2001, our silicone ignition groups designed for DAEWOO-FSO cars were granted appropriate catalogue Nos. and introduced into the technical documentation of the plant manufacturing DAEWOO cars in Warsaw. This means that we underwent all the tests confirming the quality of the groups and their usability for the so-called OEM with a positive result.
Our efforts to obtain all the certificates and quality confirmations for our products always had one goal in view. We wanted to give, and now we can even say that we give our customers GUARANTEE AN CERTAINTY that our ignition cable groups are fully professional, tested and that they have undisputable highest world quality. Their quality, especially in the “silicone version” is comparable with Bosch products and much better than that of groups coming from other renowned manufacturers.
We are proud to state that MADE IN POLAND means the highest possible quality and reliability as far as we are concerned. Therefore, having the sense of well-done duty, we invite everyone to co-operation, wishing all our customers long and unfailing use of our products.
So remember:
JANMOR MEANS THE HIGHEST QUALITY AND RELIABILITY UNDER ANY, EVEN EXTREME, CONDITIONS.